Oricom DTX4200 Dual Receive Remote Mic UHF Radio & ANU230 6.5dB HD Antenna
This is a new qulity Oricom DTX4200 UHF CB Radio Dual Channel Receive and Remote Control Speaker Mic with ANU230 6.5dB Antenna with Heavy Duty Spring Base.
The Radio (Part No: DTX4200):
An Australian First!
Like having two radios in one, the dual receive function allows you to receive and listen to two different channels simultaneously without compromising the regular features you'd expect from a UHF CB Radio
Perfect radio for any vehicle where space is limited
Simply, install the transceiver out-of-sight as the full functional ergonomic controller speaker mic has all you'll need to stay connected on and off road
Features:
- Heavy duty controller speaker microphone IP54 dust and splash resistant
- Dual receive
- Heavy duty diecast metal chassis
- Operating Volts Range: 10 to 15VDC
- 3 memory groups of 16 channels per group
- Large 96 multi-colour backlit display
- Back light brightness (5 preset levels plus auto)
- Fast scanning 80 channels within 3 seconds
- Rotary volume/channel and squelch control
- Duplex
- 38 CTCSS & 104 DCS codes
- Auto power off (off/1h/2h/4h)
- 3.5mm external jack (for optional external speaker or PA adaptor)
- Included in the pack: 2m microphone extension cable and mounting hardware
- Requires UHF CB Antenna and mounting bracket (not supplied)
Specifications:
GENERAL
- Compliance: AS/NZS 4365:2011
- Frequency Range TX/RX: 476.425 - 477.4125 MHz
- Number of TX/RX Channels: 80 UHF CB Channels (75 voice)
- Channel Spacing TX/RX: 12.5KHz
- Operating modes: Simplex, Repeater TX offset (+750KHz)
- Scanning Speed: 50 msec per channel
- Antenna Impedance: 50 Ohms
- Operating Volts nominal: 13.8VDC
- Operating Volts Range: 10 to 15VDC
- Over Voltage Protection: Diode and Voltage regulator system
- Over Current Protection: 2 AMP fuse
- Reverse Polarity Protection: Shunt diode
- Frequency stability: +/- 5 ppm
TRANSMITTER
- RF Output Power: 5 Watts max
- Modulation: F3E(FM)
- Maximum deviation: 2.5KHz
- Spurious Emissions: < -30dBm
- TX Audio pre-emphasis: + 6dB/Octave from 300Hz to 3KHz
- Current consumption during TX: 1.7 AMP with 50 ohm antenna termination
RECEIVER
- Circuit Type: Dual conversion super heterodyne
- Intermediate Frequencies: 1st IF : 21.4MHz, 2nd IF : 450KHz for Main RX; 1st IF : 38.85MHz, 2nd IF : 455KHz for Sub RX
- Receiver sensitivity: -123dBm for 12dB SINAD
- Audio output power: > 2 Watts at 8 ohm load
- RX Audio de-emphasis: + 6dB/Octave from 300Hz to 3KHz
- Signal to Noise Ratio: > 40dB
- Conducted Spurious Emission: > -57dBm
- Dimensions (H) X (W) X (D): 31mm x 128mm x 147mm
- Weight: 548g transceiver / 700g controller speaker mic
The DTX4200 recently featured on both 'What's Up Down Under' and 'Top Of Down Under'. Click on the links below to watch the videos.
What's Up Down Under
Top of Down Under
The Antenna: (Part No: ANU230)
This is a 6.5dBi ground independent UHF CB Antenna with elevated feed.
Features:
- Heavy duty barrel spring base
- 680mm fiberglass whip (full antenna height 962mm)
- 4.5m Low-loss coaxial cable, a pre-terminated FME connector and PL259 adaptor
- Requires mounting bracket (not supplied)
ITEM SPECIFICS
| Brand: | Oricom |
| Manufacturer Part Number: | DTX4200 ANU230 |
| Our Part Number: | NGDTX4200VP230 |
| Condition: | New |
Ask a question about this item
All Four x 4 Spares will always undertake to provide adequate packaging to prevent damage to products during shipping. Our responsibility for any damage to freight ends when order has left our premises. We will consider replacement of damaged product however judgement will be at our discretion. If damage has occurred during shipping it would be advised to notify us and relevant courier.
- All exchanges / credits / refunds must be returned in saleable condition with packaging, accompanied by the original invoice for proof of purchase.
- All USED mechanical parts sold carry a 3 Month parts only warranty unless otherwise specified.
- All NEW mechanical parts sold carry a 12 Month / Unlimited kilometre parts only warranty unless otherwise specified.
- All electrical parts or components sold carry a 30 Day parts only warranty unless otherwise specified.
- All Four x 4 Warranty does not cover - Labour expenses, freight or towing costs, oil leaks, broken gears, consequential damage, loss of income or any other loss or expense.
- All Four x 4 will not be liable for any repairs or work carried out, without prior approval from All Four x 4.
- Warranty is void if parts have been tampered with, modified or dismantled.
- Goods cannot be returned if they have been specially ordered or vehicle cut section.
- Goods not required must be returned within 14 Days of invoice date at purchaser’s expense. Goods will be accepted only at the Management’s discretion. If accepted for return, such goods will be subject to a 15% handling charge.
- Good will not be accepted for return if they have been fitted, unless proven faulty.
- Warranty is void for components used in performance / modified vehicles or parts / competition / off road / race applications.
- All fitment information is for vehicles released in Australia, unless specified otherwise.