IHI Turbocharger OEM suitable for Hilux KUN16 KUN26 D4D 1KDFTV 3.0 Turbo Diesel
This is a new quality IHI brand OEM Turbocharger Assembly (with Gasket Kit).
Also known as a turbo assembly.
Suitable for Toyota Hilux, KUN16, KUN26, fitted with the 1KDFTV 3.0 litre turbo diesel D4D engine, built from 2005 to 2015 runout.
Note: This IHI Turbo is OEM. and comes complete with gaskets.
Please note: If IHI isn't available, Garrett will be supplied. Please advise if this is an issue for you.
Part Number for reference: 17201-30110, 1720130110, 17201-0L040, 172010L040
Please read this fact sheet carefully:
Turbochargers are very reliable, and less than 1% of turbo’s fail due to a manufacturing fault with the turbo itself, most issues are the result of other engine related factors.
IT IS CRITICAL THE FOLLOWING ADVICE IS TAKEN INTO CONSIDERATION:
Before Replacing the Turbocharger on the above applications:
1: Visually inspect the inlet manifold for signs of carbon and soot build up, in the ports, or on the secondary butterflies.
If carbon is present remove the inlet manifold and physically clean all components fully. Failure to do so could cause premature failure of the turbocharger and may void warranty.
Loose carbon can cause turbine damage.
2: Check the vacuum operation of the secondary butterflies after cleaning and ensure they work to OEM specification. If they do not, then replace with a genuine or OEM product.
3: Visually inspect the exhaust manifold for signs of carbon and soot build up. If carbon is present remove the exhaust manifold and fully clean, removing all contamination.
Failure to do so could cause premature failure of the turbocharger and may void warranty. Loose carbon can cause turbine damage.
4: Inspect the condition of the upper engine (head) for signs of sludging of the oil. This is very common and needs to be fully cleaned to ensure no contamination can cause premature turbocharger failure.
5: Remove and inspect all fuel injectors and seals to, ensure no leakage is occurring, as this can be the cause of carbon and soot deposits due to unburnt fuel being deposited over time in the gas flow path.
If the vehicle has been tuned or has a fuel controller chip, ensure the fuel delivery rate in correct to the turbocharger boost and flow parameters. Failure to match these can cause premature turbocharger failure and may void warranty.
6: Check the condition of the Map sensor filter, and pay attention to any case cracking and internal blockages. We recommend this be replaced 100% of the time, with a turbocharger replacement.
7: Remove and clean the manifold pressure sensor and mass airflow sensor and scan test to ensure they are working correctly. If they fail the test, replace before running the vehicle as over boost from a faulty signal can fail the turbocharger and void warranty.
8: Remove, clean and inspect all intercooler and intake hoses, if the initial turbocharger failure was pumping oil into the intercooler this must be removed, cleaned and pressure tested.
9: Remove and clean the EGR valve and ensure the valve is operating freely. If the vehicle has had an EGR delete / blanking plate fitted, it is recommended it be returned to OEM specification.
10: Inspect the wiring harness and connections for the stepper motor, especially if the vehicle has been in fine dust/sand environment or through water crossings.
Should you determine a stepper motor needs replacing, please call us for price & availability.
11: Inspect the exhaust system and check for restrictions or blockages. Change in diameters of the exhaust, whereby a custom-made system has been fitted can cause flow issues and create back pressure issues inside the turbocharger and its operation.
12: Follow the universal turbocharger fitting guide.
13: Consider installing an Oil Catch Can as a preventative maintenance unit, a few options / brands are available from All Four x 4 Spares.
ITEM SPECIFICS
| Brand: | Aftermarket |
| Manufacturer Part Number: | 2042-00179 |
| Our Part Number: | NG17201-30110A |
| Condition: | New |
ADDITIONAL INFORMATION
- All Four x 4 Spares are an independent supplier of aftermarket, original equipment, and genuine parts. We are in no way related to genuine or original part manufacturers, distributors, or dealers. The warranty of any OEM genuine part is solely provided by All Four x 4 Spares
- This is an aftermarket product. Equivalent original equipment part number(s) are provided for reference purposes only.
All Four x 4 Spares will always undertake to provide adequate packaging to prevent damage to products during shipping. Our responsibility for any damage to freight ends when order has left our premises. We will consider replacement of damaged product however judgement will be at our discretion. If damage has occurred during shipping it would be advised to notify us and relevant courier.
- All exchanges / credits / refunds must be returned in saleable condition with packaging, accompanied by the original invoice for proof of purchase.
- All USED mechanical parts sold carry a 3 Month parts only warranty unless otherwise specified.
- All NEW mechanical parts sold carry a 12 Month / Unlimited kilometre parts only warranty unless otherwise specified.
- All electrical parts or components sold carry a 30 Day parts only warranty unless otherwise specified.
- All Four x 4 Warranty does not cover - Labour expenses, freight or towing costs, oil leaks, broken gears, consequential damage, loss of income or any other loss or expense.
- All Four x 4 will not be liable for any repairs or work carried out, without prior approval from All Four x 4.
- Warranty is void if parts have been tampered with, modified or dismantled.
- Goods cannot be returned if they have been specially ordered or vehicle cut section.
- Goods not required must be returned within 14 Days of invoice date at purchaser’s expense. Goods will be accepted only at the Management’s discretion. If accepted for return, such goods will be subject to a 15% handling charge.
- Good will not be accepted for return if they have been fitted, unless proven faulty.
- Warranty is void for components used in performance / modified vehicles or parts / competition / off road / race applications.
- All fitment information is for vehicles released in Australia, unless specified otherwise.