Universal Spare Wheel Carrier Jerry Can Holder Light Pole - Uni Fit
Tyre Trek Universal Towbar Mounted Spare Wheel Carrier including Dual Jerry Can Holder and 360 Degree Swivel Light Pole
This Australian designed and manufactured spare wheel carrier is designed to suit most 4WD models that are fitted with 2 inch / 50 mm square tow hitch
Forget the costly fitting expenses or rear bumper bar replacement, the Tyre Trek towbar mounted unit will save you money and provide you with the flexibility to suit your needs
This revolutionary new towbar mounted spare wheel carrier stands up to the toughest of Australian conditions
This spare wheel carrier mounts directly onto the vehicles existing towbar using the square 2 inch / 50mm tow hitch
Once fitted into the tow hitch a locking bolt is tightened to clamp the unit into position to eliminate all movement and vibration
Requires a TOWBAR with minimum towing capacity of 2000kg (& 200kg ball weight) - not to be confused with the VEHICLE towing capacity
The swing away wheel carrier provides complete access to cargo area - it locks into both the 90 and 180 degree positions with a spring loaded steel pin
The swing out arm uses a stub axle and bearing design for maximum durability
The spare wheel carrier has a high lift jack mount incorporated in the design
As some vehicles may have their number plate covered after fitting the spare wheel carrier a relocated number plate bracket including LED light is also incorporated into the design
Included with this package is:
-Swing Out Spare Wheel Carrier (incl. high lift jack mount and number plate bracket with LED light
-Dual 20L jerry can holder
-360 degree swivel light pole
Also available is a shovel holder bracket
All components are available separately
Again - please message us for further information
Fitting advise:
PLEASE CHECK YOUR VEHICLE MEASUREMENTS AGAINST THE CLEARANCE IMAGE IN THE GALLERY
Table top / tray back utes are generally not compatible as the towbar is mounted too far under the tray
Well back utes are generally compatible - check dimensions when fitting the jerry can holder
The manufacturer has fitted the Tyre Trek unit WITH dual jerry can holder to the following vehicles:
Toyota Landcruiser 80 and 100 Series. Note: Not suitable for Landcruiser 200 Series. There is a vehicle specific one for this vehicle. Please message us if you require one for a 200 series.
Nissan Patrol Y62 and Pathfinder
Nissan XTrail, although some towbars are under the required rating
Isuzu MUX and D-Max - D-Max with Hayman Reese towbars
Jeep Commander - Most Jeeps are okay
Mitsubishi Challenger - early models generally okay - during the late 90's early 2000's the towbar depth was decreased
Decreased to about 50mm - Tyre Trek requires 65mm from centre of locking pin to the back of the hitch
The manufacturer has fitted the Tyre Trek unit WITHOUT the dual jerry can holder to the following vehicles:
VW Touareg
Mitsubishi Outlander PHEV
Some wheels with a large offset may require a wheel spacer to fit on the carrier
Also available to suit light truck and bus applications - please message us for further information
Installation of the Spare Wheel Carrier:
Opening to the 90 Degree Position:
Opening to the 180 degree Position:
ITEM SPECIFICS
| Brand: | Tyre Trek |
| Manufacturer Part Number: | SWCKIT1 |
| Our Part Number: | NGSWCKIT1 |
| Condition: | New |
Ask a question about this item
All Four x 4 Spares will always undertake to provide adequate packaging to prevent damage to products during shipping. Our responsibility for any damage to freight ends when order has left our premises. We will consider replacement of damaged product however judgement will be at our discretion. If damage has occurred during shipping it would be advised to notify us and relevant courier.
- All exchanges / credits / refunds must be returned in saleable condition with packaging, accompanied by the original invoice for proof of purchase.
- All USED mechanical parts sold carry a 3 Month parts only warranty unless otherwise specified.
- All NEW mechanical parts sold carry a 12 Month / Unlimited kilometre parts only warranty unless otherwise specified.
- All electrical parts or components sold carry a 30 Day parts only warranty unless otherwise specified.
- All Four x 4 Warranty does not cover - Labour expenses, freight or towing costs, oil leaks, broken gears, consequential damage, loss of income or any other loss or expense.
- All Four x 4 will not be liable for any repairs or work carried out, without prior approval from All Four x 4.
- Warranty is void if parts have been tampered with, modified or dismantled.
- Goods cannot be returned if they have been specially ordered or vehicle cut section.
- Goods not required must be returned within 14 Days of invoice date at purchaser’s expense. Goods will be accepted only at the Management’s discretion. If accepted for return, such goods will be subject to a 15% handling charge.
- Good will not be accepted for return if they have been fitted, unless proven faulty.
- Warranty is void for components used in performance / modified vehicles or parts / competition / off road / race applications.
- All fitment information is for vehicles released in Australia, unless specified otherwise.
2 Reviews
-
10/10
Couldn't be happier, fits perfectly, looks great and was shipped quickly. Cheers guys.
-
Excellent
Terrific device, although it takes a bit of work to completely align with your car and requirements, but well worth it. Chris at allfourx4 was great to deal with, and also got more details from the supplier. Packaging and shipping were spot on.